Experiment 0 (Preface): I Have The POWER!

Multimeter reading 4.91 volts -- close enough to 5V for me to be happy.

Today I wired up the schematic from Figure S-2 (page xxvi of the Preface) on one of my new breadboards. I didn't make it all pretty like the one that Charles wired up for Figure S-1, but I'll probably clean it up a bit once I get a simple problem solved (more on that in a moment), but as you can see here, it does deliver almost 5V (4.9V give or take).


My 5VDC regulated power supply is now working... but it doesn't look exactly like the one in Figure S-2. First, I didn't have a 0.33 microfarad capacitor. (Actually, I probably do, but sometime in the past my nice organized capacitor collection became disorganized. I'm not going to point fingers at either the 7 or 4 year old boys in my household, but I'm certainly looking in their direction.)

Closeup of 5V DC Regulated Power Supply

To solve this, I went back and refreshed my memory on combining capacitors. I seem to recall that putting capacitors in parallel (versus series) was the way you added their values together. I sure hope this is true, because that's exactly what I did. I put a 0.1 microfarad and a 0.22 microfarad in parallel and no puffs of smoke have appeared.

As with Figure S-2, I added in a green LED but the more I think about it a red LED is more likely to make someone think *DANGER* so I'll swap that out later. I had plenty of 2.2k resistors in my collection as well.

Teeny tiny switch -- $0.95US

One other difference in my power supply is the On/Off switch. Charles uses what appears to be a SPDT switch but I could not find the PC-mount type to save my life. Radio Shack didn't have it, and even my trusty Atlanta-based ACK Electronics store was coming up blank until one of the associates there pulled out this little gem of a switch -- it has the low profile of a simple pushbutton component and inserted quite easily into the breadboard. Total cost -- $0.95US.


I'm not using a 9V battery. Instead, I pulled out the variable wall wart I purchased back when I was working through Make: Electronics. The ends are stripped and I soldered on a piece of red wire and black wire and added some shrink wrap to identify the leads. Those go into the breadboard as shown in Figure S-1 and after double-checking my wiring... I flipped the little power switch. The LED began to glow and no smoke was seen coming from either capacitor. (Remember: if you're using capacitors that actually have polarity, wire them up the right way -- the black stripe on the side goes towards GND.)



Here's the video describing my setup:

If you've watched the video, you now see my slight problem. The breadboard doesn't have voltage continuity down the left or right side. Maybe this breadboard requires jumper wire to connect the power and GND lines, but since the breadboard came with no documentation the only way for me to be sure is to open one up. I'm going to test this problem with the other two breadboards -- if they have a continuous power and GND line, I'll cut this first one open and share a photo of its guts in a later post.

Reading 0V when jumper wires moved down a bit.

One final observation I'd like to make about this new breadboard -- the holes are tight! Inserting jumper wires and components was tricky, and a few bent posts required a pair of pliers to fix. While I like the idea of this breadboard and how it matches some perfboard, if I continue to have these issues inserting components and wire I may very well switch back to the old standard. I'm going to give these new breadboards a few tries before making a final call.

My next tasks are transferring this wiring to a new breadboard (or two) to test the continuity of the power and GND lines as well as the ability to easily insert wires and components PLUS testing out Experiment 1.

Still Gathering Supplies

I'm still gathering a few supplies before I begin documenting my work through the new experiments. I've read ahead through Experiment 6 and I'm fast realizing that I have a LOT of supplies already in my workshop although many components are buried in various boxes and containers!

NOTE TO SELF: come up with better organization solution for all the electronics stuff I've collected over the years!

Early in the book, Charles shows two analog gauges that he purchased to enhance Experiment 2. These gauges are NOT required for the experiment, but I do want to try and tackle any extra challenges or observations he recommends in the book, so...

I could not find the 0-10 microamp analog gauge he uses, but I did find a 0-20 microamp for about the same price. I did find the 0-50 milliamp analog gauge, however. The eBay seller is gardenthing and each device was approx $5US and shipping was free.

Hopefully any of you following along and wishing to own these two gauges will find the price the same on the items as well as free shipping. My total was $10.29US (no shipping charges) and I'll be sure to post a nice pretty picture when they arrive in a week or so.



Speaking of ordered equipment -- my three new breadboards arrived along with the jumper wire (three bundles, one per breadboard!). That order was placed on May 19 and the package arrived on May 24th. Not bad.

Variable voltage plug on left (from first book), three new breadboards on right.

These new breadboards are thinner... and inserting the voltage regulator required a bit more pressure to seat properly. I was worried I would bend the prongs, but it inserted okay with no damage. I may have to trim the leads on the variable voltage adapter (purchased during my work in the first book) so they can be inserted a bit deeper into the new breadboards... just feels like components must be inserted a bit further than with my older breadboard. Will have to experiment with this a bit, and I'll be sure to let you know what I find.

I'm almost ready to go... another day or two, and I should be tackling Experiment 1. Stay tuned...

The New Breadboard

Just a quick note about breadboarding in the new Make: More Electronics book. For this new book, author Charles Platt chose to use a different breadboard design. This one has a single column of holes running down the left and right sides of the breadboard. The reasoning here (and I'm in agreement) is that having the traditional two columns (one red, one blue) running down both sides of a traditional breadboard can cause confusion for novices (and pros) as they wire up schematics. I know that I've fallen into the trap of inserting a wire into the wrong location many times.

Charles also points out that this breadboard layout also matches most designs of perfboard, so transferring a breadboarded project to perfboard is even easier.


In my quick searches, I was unable to find this type of breadboard locally, but I did manage to find them at a decent price on eBay per Charles' recommendation. I purchased three of them because I have a feeling I'll be wiring up multiple projects at once or possibly debugging a previous experiment while moving on to another one.

Here's a link to the one I bought - http://www.ebay.com/itm/310853041881

The price is $5.89US and the seller tosses in a 65 piece jumper wire set -- and I can always use more jumper wire. Shipping was cheap, too $0.79US each.

If you find this type of breadboard locally or at a cheaper price, please share in the comments so other readers can obtain one or more at the lowest price possible. It's quite possible that MakerShed may eventually offer up a Parts Pack for the new book (as they did with the first book) that might include this type of breadboard, but right now I've heard nothing about a Parts Pack being considered.

The Book Is In My Hands!

Bought the very first copy at Maker Shed

I enjoyed my visit to Maker Faire 2014 in San Mateo, California this past weekend, and I was able to get my hands on a copy of Make: More Electronics.  (As a matter of fact, I bought the very first copy from Maker Shed as I walked in when the store opened, found the book immediately and was fourth in line... no one else had a copy, so GEEK moment!)

 Even better, Charles Platt was signing copies for buyers in Expo Hall a few hours later. Although I've communicated with him a number of times over the years as I worked through Make: Electronics, I had never actually met him until this weekend. It was a real pleasure to get to visit with him for a while and chat about a number of things, not just electronics.

On the flight home, I took the chance to read through a number of the early chapters as well as skim many more. It's going to be an interesting collection of projects to try out, and I'm looking forward to sharing my results here. If you're looking for some details on the book, here you are:

* 37 chapters and 2 appendices -- a total of 36 experiments/projects to perform

* As with the first book, this one is in full-color

* Appendix B contains very detailed components lists organized into groups of projects (experiments 1-14, 15-25, and 26-36) along with itemized project-by-project listings if you wish to purchase items on a per-experiment basis.

* Errata for the book can be found here - http://www.oreilly.com/catalog/errata.csp?isbn=0636920027874

I'm already collecting some tools and components as I prepare to start working through the 36 experiments. Surprisingly, I have a lot of stuff left over from my working through the experiments in Make: Electronics that will save me some money.

I can't say when I'll be starting my work on the book's projects, but it will be soon. Tomorrow? Unlikely? Next month? Too long to wait. Give me this week or next and I expect to have enough of my tools and components pulled together to get moving.

I'm also going to leave comments open for your own thoughts, questions, observations, etc. I'll leave comments open as long as they are not abused. If I start getting a lot of spam, I'll turn on the approval process that will require me to approve a comment before it's added -- just letting you know in advance that might be coming, so don't worry if your comments stop showing up immediately... I'll get to them.

Thanks for joining me for this project -- I learned so much during my explorations for Make: Electronics, and I'm certain that Make: More Electronics will provide just as much education for all of us working through the book.

Charles Platt (left) and me

Heading to Maker Faire!

My plan is to still get a copy of the print version of More Make: Electronics and to work through it and document my work. I see the book is scheduled for a May 29 release, but I'm attending Maker Faire this weekend (May 17-18, 2014) and crossing my fingers that advanced copies of the book may be on sale in the Maker Shed.

Once I get a copy, I'll do an initial scan of the book to determine what components I will need to gather -- this could take a few days or a few weeks. My electronics collection has grown substantially and now includes many more components and tools than I ever needed for the original book. Still, I suspect I will need to do some sourcing and pricing to find out how best to gather supplies and not spend a small fortune. It's quite possible that the Maker Shed may already be planning one or more Parts Packs as they did with the first book (that one had two Parts Packs created for it), so I'll check that out and ask around at the Shed and share what I learn here.

On a similar note, I will be teaching a basic introduction to electronics and robot building to some campers this summer. At this point, I have 22 kids signed up for a weeklong camp where we'll learn about the basics of voltage, current, resistance and capacitance as well as get some hands-on practice with reading schematics, wiring them up on a breadboard, soldering, and, of course, building a real robot. I've been looking forward to this for some time, and if the camp goes well my intention is to teach more each summer and at different locations. I've got a parts supplier and a curriculum in development that I will use this first camp to help refine. The camp is $300 per camper (and I'm told this is quite low for a camp of this nature -- other non-technical camps in and around Atlanta can run $400, $500, even $600 per week. My camp filled up fast (I had originally set the cap at 20, but two extra campers managed to sign up before the school where I'm hosting it pulled the plug), so apparently parents and kids are seeing the possibilities here.

At the end of the camp, I'm inviting the parents to come and listen to their kids talk about their experience, show off their robots, and I'll have a chance to point these parents to additional resources like the Make: Electronics book and the follow-up book.

Update on Make: More Electronics

Just a quick update -- it appears the book has been pushed back from a February 2014 release to a late March release. Not a big deal -- I've written books myself that were delayed a month or two. Still looking forward to getting my copy and starting work on the projects.

A few other interesting things on the horizon. Make: magazine is going bi-monthly for a total of six issues per year (plus I'm sure they'll continue to publish those occasional special interest issues). The format will be larger and the page count is reduced, but as I understand it the larger format will still mean a bit more content than we were normally used to getting in each quarterly issue. I much prefer the more frequent issues, so this should be a good year for fans of Make: magazine.

FYI -- saw this interesting cover on the makezine.com website. Not sure if it's a mockup or not, but I sure do like the idea of building my own drone. Not sure if this is a standard issue or a special interest issue, but either way I hope it's legit.

A Review of Make: Electronics Part I

Over the Thanksgiving holiday I took some time to start re-reading the book. While I still believe that information will stick when you're using your hands to actually perform the various experiments, I didn't have the time (or the components) to start from scratch. Instead, I'm just re-reading and trying to find anything that I might have missed during my previous read and hands-on time.

This isn't the first time I've re-read Make: Electronics -- I believe it was about a year after I finished my hands-on time with the experiments that I started going back over the material again. I have the book in print and digital formats, and since I carry my tablet with me just about everywhere I go it made it fast and easy to revisit the information.

The early chapters go fast -- I'm already familiar enough with decoding resistors, for example, that I just gloss over that section. The same goes for the chapters on switching and capacitors and soldering. I've done enough of this on my own now that I believe this information is firmly seated. I think where I started really noticing more time spent actually re-reading was in Chapter 3 around Experiment 15 and the opening discussion of diodes. I just take diodes for granted when I'm taking a circuit I've found online or in a book and transferring it to the breadboard. It was nice to go back over this section and remember how "bad voltage" can creep into a circuit. It also forced me to revisit the discussion of transistors and how the different variations of transistors work to allow or disallow current flow.

I'm now up to Chapter 4 that starts the discussion on ICs. I've used quite a few ICs (including the ones I purchased for the book's experiments) over the last few years, but as I skimmed over the chapter to decide if it was worth a more detailed read, I found the 555 timer experiment and realized it wouldn't hurt to start a more in-depth review beginning with Chapter 4.

So, consider this Part I of a few upcoming posts where I'll discuss my reviews of some of the experiments as well as anything I might have forgotten and rediscovered...